Loading...
I want to use flexram to eep! MY CPU IS MK60FX512VLQ15, 1，what is D-FLAS 0 IFR abs address ? CAN I read it from IAR debug? 2，How many bytes about 1 Flash Block,1 Flash Section,where to set it?…
Kinetis MicrocontrollersWhere is this place located?
Welcome to the Kinetis Microcontrollers community. Get expert advice from the developer community. The Freescale support team also monitors these forums to provide answers and take your feedback.
Anyone can read the discussions, but only registered members of Freescale.com can post questions and comments. Before you ask a question, please search the community to find if someone has already offered a solution. If you don’t see a solution, then ask the community your question.
Hi. I will have to take a decision about selection the microcontroller. I must choice between MCF52259 and K60. Very helpful for me will be the answer for the following question: - What is the…
I inherited a project with fnet and am unclear about mqx support. This fnet has a fnet_stack/os/mqx directory but none of the downloads on sourceforge include this directory. Is mqx a supported os…
Hey guys, I'm trying to implement a simple 2 pole IIR filter on my KL25Z. Coefficients were calculated using Matlab, it's a Butterworth Highpass, second order, Fs at 10 KHz, and Cut off at 60 Hz. I'm…
Hi at all, does anyone have got an initialisation code to use the internal flash as value memory? The read and write functions itselfes aren't a problem. I tried to read the datasheet and used…
Pascal I am not clear on exactly what you are asking but I suggest looking at the uParameterSystem: http://www.utasker.com/docs/uTasker/uTaskerFileSystem_3.PDF All code needed for reading/writing…
Hi at all, does the MK20DX128 mc support the RTC second interrupt? regards
Pascal I have attached a binary for the FRDM-K20D50M which uses the 1s interrupt. - the RED LED toggles a 1s - controlled by the RTC seconds interrupt (and the green at 2.5Hz) - If you connect…
Hi all, My platform: Windows XP 32bit KEIL uVision 5.10.0.2 Board: FRDM-KE02Z EDIT: The board is already in debugging mode (flashing DEBUG-APP_Pemicro_v106.SDA from KE02_QSP). Following…
Hi Francesco, I don't have a FRDM-KE02Z on me, but I have used the P&E connection with Keil on other Freedom boards, like the FRDM-KL26Z. Here is what the "SDA_INFO.HTM" webpage, located in…
Hello, How is compatibility between K60 and K63/K64 processor? Is there comparison somewhere? Some idea? I use K60N512ZVLQ10 and i search more comfortable RAM and ROM memory size.
The bootloader and Kinetis Development Studio (KDS) already support some KL devices currently. Other devices will be added further down the line. The new K2 devices will be first along with other…
I am developing on a Freedom KL46Z board and am wanting to be able to transition over to a custom PCB. I would like to keep the simplicity of the Mbed tool chain, but I am not sure how to go about…
Would that mean having both of the MCU's connected in parallel? Also, isn't that the Serial Wire Debug port, rather than the OpenSDA port?
Hello, I have accidentally secured a MK70FX512VMJ15 device. I was trying erase flash block command and i have accidentally erased program flash memory at address 0x00000000 where are stored…
Hi Perla, I am having some problems when i try to unprotect or unsecure the flash of MK70FX512 using TCL scripts. You tested in MK60 but the flash and driver are different.…
I am trying my best to use FRDM on board OpenSDA debugger to program hex/srec/bin code into off-board KL25Z/K20 boards. I got the following errors: Keil + CMSIS-DAP firmware, SWD/JTAG…
I'm using a frdm kl05 instead kl25, the programmer didn't have problem. I have two same boards, with one i didn't have problem but with this yes.
Using the mbed-enabled FRDM-KL25Z Freedom development platform? It just got easier with a few more additions to the mbed component library! Check them out:
Now Available: The world’s Smallest ARM Powered® MCU
