Loading...
Hi ,I have mqx 4.0.2 installled on my device. I am using its web server and able to see HTML pages in IE9,Mozilla,Chrome,Safari.But when I try to open the same pages in IE11 and IE10,browser goes…
MQX Software SolutionsWhere is this place located?
Accelerate your design success with complimentary Freescale MQX RTOS, TCP/IP and USB stacks.
Welcome to the open community of MQX developers and users with the common interest of transforming applications into practically anything imaginable.
Hi, I've been using PEx for a long time and recently I've moved on MQX with my TWRK60F120M board and TWR-SER module. Now I'm trying to integrate PEx drivers into the MQX environment. Here I've got…
Hi Garabo, Thanks for your helpful answer! I read the PEx part in the tutorial, but I've got still several questions I generated PEx codes for bsp_twrk60f120m project, then tried to compile…
The MQX 4.1 Release Notes, section 5.25, page 26 is "DSPI Issues related to the DMA Usage". In here it is stated that DSPI may not work properly if there is some other user of eDMA besides it. This…
Hi, There exists a silicon issue if using "Always enabled" DMA source. While, SPI and ADC module is using eDMA, there with restriction that both modules could not do DMA transfer simultaneously.…
Hi, I'm using Ethernet communication with my K70 over MQX 3.8.1. My ethernet configuration should be: #define ENET_IPADDR IPADDR(10,4,33,50) #define ENET_IPMASK …
Hi Angel, The answer from RadekS is right. You cannot use a gateway address on another subnet. The gateway IP tells the system how to get to another subnet, and without it, packets won't leave…
Hi, I am new to freescale and quite new to embedded programming. At work we are trying to implement serialUSB communication between a main board running QNX and using devc-serusb (the serial USB…
Hi Max, Although CDC Class specification supports Bulk or Isochronous transfers, the Virtual COM example just uses Bulk transfers. You could modify the low-level USB library, by opening it, which is…
Hi, I am using mqx with twrk60f120m bsp modified to support k60fx512vlq12. i have read that flash configuration bytes is configured in vectors.c i have set config4 define to 0xffffffff, but when…
Solved. It seems i need to write config 4 0xfffffffc. 0xffffffff doesn't work. When flash is erased, the sec bit in flash reads out 0xfe. so writing 0xff doesn't work. writing 0xfc will secure the…
Hi, We've been developing about 50% of our project on the TWR-K21F120M development board with MQX. With the product's board arriving (MK22FX512VLK12, K22, 120Mhz, 80-pin package), we are torn…
Thanks for the information. We've decided to go the "bare-metal" route for this project in order to minimize possible delays. I did finish the BSP port in the end, it didn't take more than 2-3…
I am having trouble installing MFS on unformatted Flash memory. I can access the memory with FlashX, and write and read from it directly. I can install the Partition Manager over it, and attempt…
Hi All, I 've developed an application using CW10.2 and MQX 3.8.1. Now i'am making the porting of all my application on MQX4.0 but i've a problem on MFS driver creating the partiton manager.…
In that case, how to you set a devices MBR information when creating a new partition?
Hi All, I am using code warrior of v10.2 and of mqx v4.0. I created one project which based on web hvac. Here I have used the checkbox instead of radio button and project working well. But…
Hi Garabo, Thnx for reply.I have done it by using httpsrv and working perfectly...
Featuring new BSPs, driver improvements, enhanced tool support and optional IPv6 protocol support.
Whether you're just getting started, or deep into design, it's easy to get the support you need. Choose from a variety of MQX support options based on your design needs, including the improved Level 2 support plan which offers commercial-grade support, through a dedicated private support portal, phone support, priority response times, and more.