Loading...
I am using PEx 10.4 to configure the processor on a TWR-K64F120M module. I would like to read SW3 using the GPIO but the switch is wired into GPIO A4 which is also used as the NMI input. After some…
Our *.pe file is attached. Thanks!
Processor Expert SoftwareWhere is this place located?
Announcement 1 Processor Expert Software Microcontroller Driver Suite v10.4
Welcome. Our tag line is "Write Your Code Here" because that's the comment you see everywhere in the code that Processor Expert Software generates. It creates the framework and tells you where to fill in the blanks so you can focus on the places where you really add value. This tool creates reusable components that are hardware- and operating-system-agnostic.
In the community, you can find resources, get and give advice, as well as share components with other developers. For everyone's benefit, please mark answered questions as such! This greatly helps everyone locate the correct answers quickly, and also highlights those questions still in need of help.
 | Microcontroller Driver Suite v10.4 is a software management system that generates C code to create, configure, optimize, migrate and deliver software components, such as peripheral drivers, for Kinetis and ColdFire+ processors. The driver suite is delivered and installed as a comprehensive product with the Eclipse 4.2 (Juno) IDE. It is also available as an Eclipse plug-in for existing Eclipse 3.7 (Indigo) and Eclipse 4.2 (Juno) installations.
|
We see lots of MISRA violations when looking at drivers produced for the MK64 microcontroller. Our initial assumption was that this code was not meant to be compliant (with MISRA C 2004) but I…
Hi all, I am testing GPIO based touch sensing on the FRDM-KE02Z board, which features a two-electrodes analog slider. In the Quick Start Package, I have found the precompiled example (shipped…
Does anyone know when we will see support for the K70 in the DDR validation tool? I'm assuming that it will be in an update to CW10.6 since the K70 is already supported by CW10.6 as well as the new…
I can remove other components, but the asynchronous serial component has the remove option grayed out.
I figured it out. If you right click the asynchronous serial component in the hardware view, the delete option is grayed out. You can delete any other kind of component here but asynchronous serial…
Hi All, I had an SCI issue with CW 10.4 and installed 10.6 which fixed it, looks like the Enter Critical wasn't disabling interrupts as the Buffer was good, but the output pointer was getting…
Hi Petr, Thanks for confirming the issue. Your solution is the same is what I used to patch around it. Regards, Darren
Hi! I'm trying to use the Ethernet_LDD driver generated by PEx (v10.4) to control an external Ethernet PHY chip. I also use the code in "Tpyical Usage" of the "Helps on Component". To configure…
Hi, 1. Capability bits (10/100Mbps half/full duplex) have permanent values reflecting the abilities of the PHY chip. These don't change. 2. You must select MII or RMII according to your component…
I am using the current PE10.4 with the MK10DN512VLL10 processor. I am setting 5 channels up as single ended inputs. The issue is that two channels read correctly and three channel read either full…
Hi, Thank you, now I see that it's a different issue. You have identified it correctly, there is a problem in the ADC_LDD initialization code in the latest Processor Expert Driver Suite 10.4. It…
Hi I am using K60 uc and receiving data over UART in continuous form, beside the data I am doing other processing but due to UART my program is getting delayed so I wanted to use DMA so that both…
Hi Petr I Due to some technical fault in my K60 board I was not able to test your code instead I Copied the settings to a K20D50M- FRDM board but it didn't work Can you please check out what I am…
I install codewarrior 10.6, and when I try to add an ADC component and generate the code, codewarrior has this error : Unexpected status of srcipt: Beans\ADC\ADC_LDD.chg, please contact freescale…
Additional note - for now, if you don't need specifically ADC component, use the ADC_LDD component instead. The ADC is internally using ADC_LDD anyway. Generally, the 'ADC' is still available for…
I had updated to PE10.4 last week and now we are having issues with the ADC channels reading data back. What I am seeing is for ADC1 when we are selecting the ADC channel to use the MUXSEL "a" or…
I had a similar problem, see here https://community.freescale.com/thread/322442 Regards, Darren
I'm new to the Kinetis family. I am trying to use Processor Expert, as I really like the idea — but even with seemingly simple tasks I end up running into huge problems. Here's an example. I…
Wow, PEx is really simple to use when you have the components for your cpu model! (see this post: There is a Time and Date for both Worlds | MCU on Eclipse ) One thing I realized is that in all…
Hi, I have just installed Processor Expert 10.4 and loaded the project for the TWR-K60F120M that I have previously used with Processor Expert 10.3. I have not knowingly made any changes from the…
Thanks Petr, I’ll look forward to the reply back from the development team…. Gregory T. Powanda Senior Field Applications Engineer Arrow Electronics, Inc. 3245 Old Frankstown…
Hello! I'm working on the FRDM-K20D50M evaluation board and I use Eclipse-based Processor Expert to create a project.But I've got some troubles with GPIO configuration in the Processor Expert. I'm…
Thanks
Hi I am using K60 connected with SD card and using FATfs library present in Processor Expert. I want to write to file as the interrupt is triggered in Event.c. but I am having problem in writing to…
Hi Actually I am having various sensors which is sending data at around 100Hz which is time stamped so for different sensors I wanted to have separate files with time stamped so for higher accuracy…
